image stats
rating
3.03
votes
84
views
2185
uploader
Mrkim
comments
10
date added
2011-09-05
category
Sport
previous votes
Loading..
Round 4 - WTF are these?
1 star2 stars3 stars4 stars5 stars
Round 4 - WTF are these?

"a close-up of a screwdriver"

Rate image:
[ | | ]
[ | ]
Comments for: Round 4 - WTF are these?
90130_ Report This Comment
Date: September 05, 2011 04:26AM

Easy, from left; Grease zerk fitting adapter, grease fitting extractor and threading tap, motorcycle chain pin extractor, and a motorcycle cable lubricator.

I deserve an ice cold Heineken.
BlahX3 Report This Comment
Date: September 05, 2011 04:30AM

#2 is a tap

#3 is set pin remover

#4 is a wire clamp
Mrkim Report This Comment
Date: September 05, 2011 04:54AM

If you can tell me what that grease zerk adapter is designed for doin 9er you're certainly due a frosty cyber Heine smileys with beer

smoking
smiley
90130_ Report This Comment
Date: September 05, 2011 05:09AM

I had to think about it for a bit, but realized I have this same damn tool in my rollchest drawer with some BMW service tools...

It's a pilot bushing extractor, for removal of bronze bushings from a blind hole in automotive flywheels. Hydraulic pressure from the grease forces out the bushing.
Mrkim Report This Comment
Date: September 05, 2011 05:22AM

Que the buzzer Johnny!!!

Think a bit more buddy, you're in the ballpark, just poppin flies at the moment though grinning smiley

I usually use a clutch pilot tool I have with different sized screw on tips for removin those bushings. I just pack the hole in the butt end of the crank with grease and then use the alignment tool and a hammer to compact the grease and pop out the bushing/bearing, as the case may be. Works like a champeen Dancing Green Banana!

smoking
smiley
90130_ Report This Comment
Date: September 05, 2011 05:41AM

Hmmm. Ok, come to think of it, the BMW Krautenschlager whathefuck in my tool box is indeed different. More clues?? I'm gettin' tired and I want my fucking Heineken. Hey...you are in big D, right? Isn't gettin' late for you?
Mrkim Report This Comment
Date: September 05, 2011 05:52AM

Ok, one hint and I'm off to catch a few Zs. The tool is a 2 part assy, the section furthest from the zerk threads off so you can slip it over the part before screwin it back together and whippin out the grease gun to work its magic.

I'll check back with you cats in the mornin and see if anyone else manages to collect some tasty cyber frostiessmileys with beer

smoking
smiley
SpazzII Report This Comment
Date: September 05, 2011 05:31PM

Drug paraphernalia?
Mrkim Report This Comment
Date: September 05, 2011 05:47PM

Geez Spaz I dunno what your favorite chemicals might be but then again, if any of the above would be used in preppin 'em I'd be worried about joinin in the fun. Instead, I think I'll just stick with my left handers eye
popping smiley

smoking
smiley
Mrkim Report This Comment
Date: September 17, 2011 01:51AM

Since 9er got close and no one else has taken a swing at it, the far left item is a 2 piece cable greasing fixture. You unscrew it and slip one 1/2 of it over the end of a cable housing and then slide the cable and end barrel into the other 1/2 of the tool then screw the 2 halves together. hit the zerk with a grease gun and grease if forced through the cable housing. Once you see grease comin outta the other end of the cable housing you're done.

Greasing a cable actually does a better job of keeping the lubricant in place than it does to just oil the cable like the tool on the far right is designed for winking
smiley

smoking
smiley